Heat sink producer for both custom and standard heat sinks Home | Contact Us | About Aavid | Sales Rep Log Incustom and standard heat sinks
Heat Sinks
Heat sinks, Extrusion Profiles, Interface Materials, Heat sink Attachments, request heat sink sample, rfq, more Custom, Software, Design Process, Thermal Assemblies, CFD, Model Shop  How to select a heat sink, Charts and Graphs, Thermal Resistance, Dimentional Tolerances, Correction Factors, Forced Convection Table Sales Reps, Distributers, RFQ, Literature, Ordering Information Thermal solution trade shows, heatsink trade shows  

Search

Search by part #  

  Check distributor
  part inventory
 

Heat sinks - extrusions, boardlevel, copper, aluminum

 Browse Heat sinks  
 
 
 
 



  Useful Links
 • Building a part #
 • Catalog Request
 • Directions
 • Find Distributor
 • Find Sales Rep
 • How to order?
 • MSDS Safety Sheets
 • Part # Cross Ref
 • Quote Request
 • RoHS Initiative
 • Sample Request


Products / Extrusions / Correction Factors
Temperature Correction Considerations
Since natural convection heat sink efficiency degrades with decreasing sink-to-ambient temperature differential, a correction factor must be applied to the published data if an application requires a sink-to-ambient temperature rise of less than 75°C. The corrected thermal resistance is obtained by multiplying published °C/W/3-in data by the appropriate factor from the following table:
Temperature Rise (DTsa) Correction Factor
75°C 1.000
70°C 1.017
60°C 1.057
50°C 1.106
40°C 1.170
30°C 1.257

For any extrusion profile in natural convection,
the thermal resistance (°C/W) is more than 25% higher
at DTsa = 30°C than at DTsa = 75°C.
Length Correction Considerations

The published extrusion data shows natural convection performance for a three inch section with a centrally located point source heat load. Because the heat load is assumed to be at a point rather than uniformly distributed, thermal resistance does not change linearly with length. (The ends of a very long extrusion would be cooler than the center and therefore the transfer of heat to the surrounding air is little, if any.) It is therefore necessary to apply a correction factor to published data for extrusion lengths shorter or longer than three inches. The corrected thermal resistance for different lengths of extrusion is obtained by multiplying published °C/W/3-in data by the appropriate factor from the following table:
Heat Sink Length Correction Factor
1.0 inch (25.4mm) 1.80
2.0 inch (50.8mm) 1.25
3.0 inch (76.2mm) 1.00
4.0 inch (101.6mm) 0.87
5.0 inch (127.0mm) 0.78
6.0 inch (152.4mm) 0.73
7.0 inch (177.8mm) 0.67
8.0 inch (203.2mm) 0.64
9.0 inch (228.6mm) 0.60
10.0 inch (254.0mm) 0.58
11.0 inch (279.4mm) 0.56
12.0 inch (304.8mm) 0.54
13.0 inch (330.2mm) 0.52
14.0 inch (355.6mm) 0.51
15.0 inch (381.0mm) 0.50

This Extrusion Length Correction Factor Table can also be used to determine the length of extrusion required to obtain a desired thermal resistance. Divide the desired thermal resistance by the published thermal resistance for a three inch section to obtain the correction factor, which can be used to determine the correct length.

EXAMPLE: Extrusion 62465 has a thermal resistance of 8.0 °C/W/3-in. A five inch piece will have a thermal resistance of 6.24°C/W, using the appropriate length correction factor of 0.78 [i.e. 8.0°C/W x 0.78 = 6.24°C/W].

Since the thermal resistance of 6.24°C/W is at a temperature rise of 75°C, the resistance of the heat sink at a temperature rise of 50°C will be increased by the temperature correction factor of 1.106 from the Temperature Rise Correction Factor Table. Therefore the new natural convection thermal resistance at 50°C is 6.90°C/W [6.24°C/W x 1.106 = 6.90°C/W].

Performance Factor Table








Home  • Sitemap  • Disclaimer Statement  •  ©2008 Aavid Thermalloy, LLC